Emulator Borad Key Programmer Immobilizer IMMO EWS 2/3.2 Diagnostic Repair Module

239,00 kr
gratis leverans

Emulator Borad Key Programmer Immobilizer IMMO EWS 2/3.2 Diagnostic Repair Module

  • Märke: Unbranded

Emulator Borad Key Programmer Immobilizer IMMO EWS 2/3.2 Diagnostic Repair Module

  • Märke: Unbranded
Rekommenderat återförsäljningspris: 319,00 kr
Pris: 239,00 kr
Du sparar: 80,00 kr (25%)
Säljs av:
239,00 kr
gratis leverans

I lager

Vi erbjuder följande betalsätt

Beskrivning

Feature: 1. Emulator of superior quality, can emulate EWS 2 and EWS 3.2 immobilizer (EWS module). 2. Ideal solution for unrecoverable old system(faulty EWS, lost or damaged transponders, continuous problems with rolling codes etc.). 3. No counters or car starts limited, allows you to change and store new ISN without any limitations. 4. There is clear installation instructions in the specification, reduce the difficulty of installation. 5. Small in size yet outstanding in performance, practical auto diagnostic service tool. Specification: Item Type: Emulator Material: ABS + MetalSize(L x W): Approx. 27 x 18mm/1.1 x 0.7inFunction: This device can emulate EWS 2 and EWS 3.2 immobilizer (EWS module) in cases when old system restore is impossible (faulty EWS, lost or damaged transponders, continuous problems with rolling codes etc.).In case of EWS3.2 similar procedure is used, only difference is that that it is NOT connected directly to diagnostic for K-line.How to Use:1. Remove old EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted.2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and start EMULATOR CONFIGURATION UTILITY. 3. Choose COM port, write in desired ISN number, press button Store.4. For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option "ECU xxxxx", press Read. Software will try to read ISN. If successful,chooseoption "EWS emulator" and press button Store to save ISN number into emulator.5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to DME(DDE) <-> EWS line.6. Don't forget to short two starter relay wires (EWS connector)! 7. Car is ready to start.. Package List: 1 x Emulator Note: Emulator is shipped with JUMPER 1 shorted. For testing purposes ISN 0579 is stored by default. Please allow 0‑2mm error due to manual measurement. Thanks for your understanding.
  • Fruugo-ID: 412095698-871546245
  • EAN: 7603816662627

Produktsäkerhetsinformation

Se produktsäkerhetsinformationen som är specifik för denna produkt som beskrivs nedan

Följande information tillhandahålls av den oberoende tredjepartsåterförsäljaren som säljer denna produkt.

Produktsäkerhetsetiketter

CE Mark
Säkerhetsvarningar: Warning: Please read the product instructions carefully before use to ensure correct use.
Serienummer: 7603816662627

Leverans och returer

Skickas inom 2 dagar

  • STANDARD: GRATIS - Leverans mellan kl tis 07 oktober 2025–tis 14 oktober 2025 - GRATIS

Leverans från Kina.

Vi gör vårt bästa för att säkerställa att produkterna du beställer levereras kompletta och enligt dina specifikationer. Om du däremot skulle ta emot en ofullständig beställning, eller andra artiklar än de du beställt, eller om det finns någon annan anledning till att du inte är nöjd med din beställning, kan du returnera beställningen, eller valfria produkter som ingår i beställningen, och få fullständig ersättning för artiklarna. Visa fullständig returpolicy

Produktöverensstämmelsedetaljer

Vänligen se överensstämmelseinformationen som är specifik för denna produkt som beskrivs nedan.

Följande information tillhandahålls av den oberoende tredjepartsåterförsäljaren som säljer denna produkt.

Tillverkare:
Följande information beskriver kontaktuppgifter för tillverkaren av denna produkt som säljs på Fruugo.

  • Wuhan Jinxingkai Network Technology Co., Ltd.
  • Wuhan Jinxingkai Network Technology Co., Ltd.
  • No. 1-1, Door 57
  • Shihua Village
  • Qingshan District
  • Wuhan
  • CN
  • 430000
  • goldxinks@163.com
  • 0086 17786498762
  • https://shop01473o1711614.1688.com/page/creditdetail.htm?spm=a261y.7663282.shopNavigation.1.6310755czE9SFQ

Ansvarig person i EU:
Följande information innehåller kontaktuppgifter för den ansvariga personen i EU. Den ansvariga personen är den utsedda ekonomiska aktör i EU som ansvarar för att skyldigheterna uppfylls för denna produkt som säljs till Europeiska unionen.

  • None
  • Kequ Technology s.r.o.
  • Pražákova 1008/69
  • Štýřice
  • Jihomoravský kraj
  • Brno
  • CZ
  • 63900
  • christopher25106@outlook.com
  • 420608214795