Emulator Module,Emulator Borad Key Programmer IMMO Emulator Emulatorfor EWS Optimal Efficiency

309,00 kr
gratis leverans

Emulator Module,Emulator Borad Key Programmer IMMO Emulator Emulatorfor EWS Optimal Efficiency

  • Märke: Unbranded
Säljs av:

Emulator Module,Emulator Borad Key Programmer IMMO Emulator Emulatorfor EWS Optimal Efficiency

  • Märke: Unbranded

309,00 kr

Bara 8 kvar i lager
gratis leverans

14-dagars returpolicy

Säljs av:

309,00 kr

Bara 8 kvar i lager
gratis leverans

14-dagars returpolicy

Betalningsmetoder:

Beskrivning

Emulator Module,Emulator Borad Key Programmer IMMO Emulator Emulatorfor EWS Optimal Efficiency

Features 1、Emulator of superior quality, can emulate EWS 2 and EWS 3.2 immobilizer (EWS module). 2、Ideal solution for unrecoverable old system(faulty EWS, lost or damaged transponders, continuous problems with rolling codes etc.). 3、No counters or car starts limited, allows you to change and store new ISN without any limitations. 4、There is clear installation instructions in the specification, reduce the difficulty of installation. 5、Small in size yet outstanding in performance, practical auto diagnostic service tool. Specification Item Type: Emulator Material: ABS + Metal Size(L x W): Approx. 27 x 18mm/1.1 x 0.7in Function: This device can emulate EWS 2 and EWS 3.2 immobilizer (EWS module) in cases when old system restore is impossible (faulty EWS, lost or damaged transponders, continuous problems with rolling codes etc.). In case of EWS3.2 similar procedure is used, only difference is that that it is NOT connected directly to diagnostic for K-line. How to Use: 1. Remove old EWS2 control unit, find +12v ACC, GND, K-line wires, attach emulator. Emulator must be in service mode: JUMPER 1 shorted. 2. Connect ANY K-line diagnostic adapter to vehicle diagnostic connector and start EMULATOR CONFIGURATION UTILITY. 3. Choose COM port, write in desired ISN number, press button Store. 4. For some ECU s it is possible to read ISN number directly from engine control unit. In this case select option "ECU xxxxx", press Read. Software will try to read ISN. If successful, chooseoption "EWS emulator" and press button Store to save ISN number into emulator. 5. Disconnect emulator from K-line, remove JUMPER 1 and connect K output from emulator to DME(DDE) <-> EWS line. 6. Don't forget to short two starter relay wires (EWS connector)! 7. Car is ready to start. Package List 1 x Emulator
  • Fruugo-ID: 278988261-620533105
  • EAN: 9797733492134

Leverans och returer

Skickas inom 10 dagar

  • EXPRESS: GRATIS - Leverans mellan kl tis 13 januari 2026–ons 14 januari 2026 - GRATIS - Snabbast

  • STANDARD: GRATIS - Leverans mellan kl tis 20 januari 2026–tis 27 januari 2026 - GRATIS

Leverans från Kina.

Vi gör vårt bästa för att säkerställa att produkterna du beställer levereras kompletta och enligt dina specifikationer. Om du däremot skulle ta emot en ofullständig beställning, eller andra artiklar än de du beställt, eller om det finns någon annan anledning till att du inte är nöjd med din beställning, kan du returnera beställningen, eller valfria produkter som ingår i beställningen, och få fullständig ersättning för artiklarna. Visa fullständig returpolicy